With this 65 W USB-C PD power supply (with GaN technology) and the included USB-C cable you can start using the FNIRSI HS-01 soldering iron straight away. Of course, you can also use this charger to fast charge your tablets and smartphones via USB-C and USB-A. Included 65 W USB-C PD GaN Power Supply (EU) USB-C cable (1.2 m)

Read more less

The FNIRSI 1013D is a fully featured 2-channel tablet oscilloscope with a high-resolution 7-inch LCD screen (800 x 480 pixels). The oscilloscope has a real-time sampling rate of 1 GSa/s and an analog bandwidth of 100 MHz. With full trigger functions (single/normal/automatic), it can be used for periodic analog signals or non-periodic digital signals. The built-in high-voltage protection module can withstand a continuous voltage of up to 400 V. Features Intelligent anti-burn,1X can withstand up to 400 V withstand voltage. 100 MHz analog bandwidth @ 1 GSa/s sampling rate (1X = 5 MHz,10X = 100 MHz). Fully fit 7-inch 800 x 480 resolution color TFT LCD display with bright colors and high contrast. Capacitive touching screen, the same as the touching mode of modern mobile tablet, is not a resistive touching screen with ancient nail operation. High measurement voltage range, 1X can measure 0~40 V, 10X can measure 0~400 V,100X can measure 0~4000 V. Up to 12 parameters measurement: VPP, VP, Vmax, Vmin, Vavg, Vrms, Frequent, Duty+, Duty-, Time+, Time−, Period. Cursor measurement function, it is convenient to manually measure the period and frequency and voltage. Complete triggering function (single, normal, automatic). At any time, the waveform display (pause function) is frozen. Equipped with high efficiency One-button AUTO. One-button waveform storage and screenshot. Built-in 1 GB storage space, can store up to 1000 screenshots + 1000 sets of waveform data. Powerful waveform picture manager supports thumbnail browsing, viewing, detailed viewing, page turning, deletion and waveform zooming in, zooming out, moving, etc. Equipped with a USB interface, which can be connected to a computer to share its screenshots with the computer, which is convenient for secondary analysis. Lissajous figures graphic display function can be used to determine the amplitude, frequency, and phase contrast of two groups of signals. FFT display function, can analyze the spectral characteristics of the signal. Built-in 6000 mAh rechargeable lithium battery, fully charged for 4 hours of continuous use at the highest screen brightness. Memory compression technology, waveform refresh screen does not flicker. Screen brightness adjustment. Background grid brightness adjustment. Applications Electronic DIY Appliance repair Car repair Equipment debug Scientific research Product development Specifications Channels 2 LCD size 7 inch LCD resolution 800 x 480 Display technology TFT Bandwidth 100 Mhz Sampling rate 1 GSa/s Rise time <3nS Storage depth 240 Kbit Input resistance 1 MΩ Sensitivity 50 mV ~ 500 V Time base 50S ~ 10nS Trigger mode Single/Normal/Auto Trigger edge Rising/Falling Coupling AC/DC Highest test voltage 1X: 40 V, 10X: 400 V Cursor Position XY, Trigger Y Roll mode Yes One button AUTO Yes Waveform storage 1000 pictures + 1000 waveforms Waveform manager Yes Voltage accuracy ±2% Frequency precision ±0.01% high precision Parameter 12 kinds in total Battery 6000 mAh Lithium Standby 4 hours Extension USB export Power supply USB-C, 5 V @ 2 A/3 A/4 A Dimensions 184 x 124 x 50 mm Weight 650 g Included 1x FNIRSI 1013D 2-ch Tablet Oscilloscope 2x 100 MHz Probes (1X and 10X) 1x USB charger 1x USB cable 1x Manual Downloads Manual Firmware

Read more less

The FNIRSI 2C23T is a fully functional, highly practical 3-in-1 dual channel digital oscilloscope with a high resolution 2.8-inch LCD display (320 x 240 pixels) designed for the maintenance and development industry. This device is equipped with 3 main functions: oscilloscope, multimeter and signal generator. The oscilloscope has an FPGA+MCU+ADC hardware architecture with a sampling rate of 50 MS/s, an analog bandwidth of 10 MHz and a built-in high-voltage protection module that supports the measurement of peak voltages of ±400 V maximum. The multimeter has a 4-digit 10000-point RMS value and supports AC/DC voltage and current measurements, as well as capacitance, resistance, diode, on/off and other measurement functions. Equipped with a built-in DDS function signal generator, it can output 7 kinds of function signals, with a maximum output of 2 MHz for all signals and a step of 1 Hz; the output frequency, amplitude and duty cycle are adjustable. The built-in 3000 mAh rechargeable lithium battery achieves a standby time of up to 6 hours. Features 2-ch oscilloscope 10 MHz bandwidth 50 MS/s real-time sampling rate 7 signal waveforms 10000 counts 2.8' HD color display (320 x 240 pixels) Dimensions: 167 x 89 x 35 mm Weight: 300 g Specifications Oscilloscope Dual channel, 2x 10 MHz bandwidth, 50 MS/s real-time sampling rate Maximum measured voltage: ±400 V FPGA+ADC+MCU high-performance hardware architecture, capturing waveform details without loss Equipped with complete triggering functions (auto, single, normal) Equipped with efficient automatic adjustment, the measured waveform can be displayed without complicated adjustment Save waveform screenshots, supports exporting images to a computer, facilitate secondary waveform analysis Multimeter 4-bit integer 9999 counting True RMS measurement Identification of voltage, current, capacitance, resistance, diode, on/off, and zero live wire Maximum input voltage: AC 750 V, DC 1000 V Automatic range, intelligent anti burning Data retention, color screen digital display Signal Generator 7 signal waveforms: sine wave, square wave, triangular wave, full wave, half wave, noise wave, DC Output frequency: 1 Hz-2 MHz Output amplituade: 0.1-3.3 V Output duty cycle: 0-100% Included 1x FNIRSI 2C23T (3-in-1) 2-ch Oscilloscope 1x P6100 oscilloscope probes (10X) 1x Multimeter probe 1x Crocodile clip probe 1x USB-C charging cable 1x Manual Downloads Manual

Read more less

The FNIRSI 2C53P is a powerful 2-channel oscilloscope with a 50 MHz bandwidth and 250 MS/s sampling rate, ideal for electronics professionals, makers, and students. It offers precise measurements up to ±400 V, a 4.5-digit True RMS multimeter, and an integrated signal generator for versatile applications. With a 4.3-inch color touchscreen and a 4000 mAh battery providing up to 4 hours of use, the FNIRSI 2C53P combines functionality and convenience in one compact device. Specifications General Display 4.3" TFT Color Touch screen (480 x 272) Power Supply USB-C (5 V/2 A) Battery 4000 mAh Lithium battery Languages Chinese, English, Russian, Japanese, Spanish, Portuguese, German, Korean Dimensions 145 x 98 x 35 mm Weight 360 g Oscilloscope Channels 2 Bandwidth 50 Mhz Real-time sampling rate 250 MSa/s Storage Depth Up to 64 kByte Time base range 10 ns/div – 10 s/div Vertical Sensitivity 10 mV/div – 10 V/div Waveform Display Mode YT/XY/scroll Vertical Resolution 8 bits Input Impedance 1 MΩ Bandwidth limit Support 20 MHz limit Probe Attenuation Coefficient 1x/10x Input Coupling AC/DC Trigger Type Rising/Falling edge Peak Voltage ±400 V Trigger Level Range 8 cells (positive/negative) Trigger Mode Auto/Normal/Single Storage Space 13 MB Measured Data Period, frequency, peak-to-peak value, maximum value, minimum value, average value, effective value, amplitude, duty cycle, pulse width Multimeter Function Range Accuracy DC Voltage 1.9999V/19.999V/199.99V/1000.0V ±(0.5%+3) AC Voltage 1.9999V/19.999V/199.99V/750.0V ±(1%+3) DC Current 19.999mA/199.99mA/1.9999A/9.999A ±(1.2%+3) AC Current 19.999mA/199.99mA/1.9999A/9.999A ±(1.5%+3) Resistance 19.999MΩ/1.9999MΩ/199.99KΩ/19.999KΩ ±(1.5%+3) 1.9999KΩ/199.99Ω ±(0.5%+3) Capacitance 999.9uF/99.99uF/9.999uF/999.9nF/99.99nF/9.999nF ±(2.0%+5) 9.999mF/99.99mF ±(5.0%+20) Temperature −55~1300°C (−67~2372°F) ±(2.5%+5) Diode/ON-OFF Yes Signal Generator Different Waveform Output Frequencies Sine wave: 10 MHzOther waveforms: 5 MHz Waveform Frequency 0-10 MHz Waveform Amplitude 0.1-3.0 V Square Wave Duty Cycle 0-100% Included 1x FNIRSI 2C53P (3-in-1) 2-ch Oscilloscope 2x P6100 Probes (100 MHz) 1x Multimeter Probe 1x Alligator Clip Probe 1x USB Cable 1x Manual Downloads Manual Firmware V1.8

Read more less

The updated FNIRSI 2C53T, an enhanced version of its 10 MHz predecessor, is a compact and versatile 3-in-1 device. It combines a dual-channel 50 MHz oscilloscope, a 4.5-digit True RMS multimeter, and a signal generator with 13 waveform types, making it an essential tool for maintenance and research professionals. Oscilloscope: Features 50 MHz bandwidth, 250 MS/s sampling rate, ±400 V protection, FPGA + ARM + ADC architecture, and waveform saving for analysis. Multimeter: 4.5-digit True RMS with 19999 counts, supports AC/DC voltage, current, capacitance, resistance, diode, and continuity measurements. Signal Generator: Outputs 13 signal types up to 50 KHz, with adjustable frequency, amplitude, and duty cycle. With a 2.8-inch LCD, 3000 mAh battery (6-hour runtime), and a portable design, it delivers powerful functionality in a user-friendly package. Specifications Oscilloscope Channels 2 Analog Bandwidth 50 MHz Real-time Sampling Rate 250 MS/s Storage Depth 1 Kpts Impedance 1 MΩ Time Base Range 10ns-20s Vertical Sensitivity 10 mV/div-10 V/div (x1) Maximum Measured Voltage ±400 V Trigger Mode Auto/Normal/Single Trigger Type Rising edge, Falling edge Display Mode Y-T/Rolling/X-Y Coupling Method AC/DC Persistence OFF, 500ms, 1s, ∞ Math 8 Basic Operations + FFT Supported Waveform Screenshot Save, Export Waveform Image, Cursor Measurement, Infinite Afterglow Multimeter DC Voltage 1.9999V/19.999V/199.99V/1000V ±(0.5%+3) AC Voltage 1.9999V/19.999V/199.99V/750.0V ±(1%+3) DC Current 19.999mA/199.99mA/1.9999A/9.999A ±(1.2%+3) AC Current 19.999mA/199.99mA/1.9999A/9.999A ±(1.5%+3) Resistance 19.999MΩ/1.9999MΩ/199.99KΩ/19.999KΩ ±(0.5%+3) 1.9999KΩ/199.99Ω ±(2.0%+3) Capacitance 999.9uF/99.99uF/9.999uF/999.9nF/99.99nF/9.999nF ±(2.0%+5) 9.999mF/99.99mF ±(5.0%+20) Temperature −55~1300°C (−67~2372°F) ±(2.5%+5) Continuity Test Yes Diode Yes Signal Generator 13 Signal Waveforms Sine wave, rectangular wave, sawtooth wave, half wave, full wave, positive step wave, reverse step wave, exponential rise, exponential fall, DC, multi-audio, Sinker pulse, Lorentz wave Output Frequency 0-50 KHz Output Amplitude 0-3 V Output Duty Cycle 0-100% General Display 2.8" HD color screen Resolution 320 x 240 Charging USB-C (5 V/1 A) Battery 3000 mAh Lithium battery Standby Time 6 hours Languages English, Chinese Dimensions 167 x 89 x 35 mm Weight 300 g Differences New vs Old Version Model 2C53T Upgrade 2C53T Predecessor Bandwidth 50 MHz 10 MHz Display Mode Y-T/Rolling/X-Y Y-T/Rolling Math 8 Basic Operations + FFT N/A Cursor Function Yes N/A XY Lissau Graph Yes N/A Afterglow Function Yes N/A Multimeter Accuracy 19999 Counts 9999 Counts Signal Generator 50 KHz 2 MHz Included 1x FNIRSI 2C53T Upgrade Oscilloscope (50 MHz) 2x P6100 Oscilloscope probes (10X) 1x Multimeter probe 1x Alligator clip probe 1x USB-C charging cable 1x Storage bag 1x Manual Downloads Manual Firmware V1.0.3

Read more less

The FNIRSI DMC-100 is a high-precision 10,000-count True RMS clamp multimeter for engineering, labs, vehicle repairs, and home diagnostics. It measures up to 750 V and 600 A with three modes (routine, waveform, and power) along with NCV detection for added safety. Its 2.0-inch color TFT display offers clear readings, data visualization, and adjustable brightness. A 1500 mAh rechargeable battery with auto power-off ensures long use, while a flashlight, backlight, and data storage enhance usability, making it a reliable tool for professionals and DIYers. Features 10,000-count smart True RMS clamp meter for accurate readings Supports up to 750 V voltage and 600 A current 2.0-inch full-color TFT screen (240 x 320) for clear visuals New UI with data curve display for easy reading at a glance Switch freely between general measurement, waveform display, and power measurement modes Non-contact voltage measurement and zero/fire line identification Measures temperatures from −55°C to 1300°C Built-in battery (3.7 V/1500 mAh) for extended usage Convenient charging and data transmission via USB-C port Includes an LED light, screen backlight, and data-saving capabilities Intelligent automatic shutdown to conserve battery life Easily switch between temperature units (°C/°F) Screen brightness is adjustable for various environments Supports firmware updates to enhance functionality Specifications DC Voltage 9.999V/99.99V/999.9V ±(0.5%+3) AC Voltage 9.999V/99.99V/750.0V ±(1%+3) DC Current 99.99A/600.0A ±(2.5%+10) AC Current 99.99A/600.0A ±(2.5%+10) Resistance 9.999MΩ/999.9KΩ/99.99KΩ/9.999KΩ/999.9Ω ±(1.5%+3) 99.99MΩ ±(1.5%+3) Capacitance 999.9μF/99.99μF/9.999μF/999.9nF/99.99nF/9.999nF ±(2.0%+5) 9.999mF/99.99mF ±(5.0%+20) Frequency 9.999MHz/999.9KHz/99.99KHz/9.999KHz/999.99Hz/99.99Hz/9.999Hz ±(0.1%+2) Temperature −55~1300°C (−67~2372°F) ±(2.5%+5) Continuity Test Yes Diode Yes NCV Yes LIVE Yes Display 2.0" TFT Color Screen Power Supply 3.7 V/1500 mAh Lithium Battery Charging 5 V/1 A (USB-C) Maximum Jaw Size 25 mm Dimensions 193 x 74 x 32 mm Weight 194 g Included 1x FNIRSI DMC-100 Clamp Meter 1x Multimeter pen 1x Temperature probe 1x USB charging cable 1x Manual Downloads Manual Firmware V1.3

Read more less

The FNIRSI DMT-99 is an intelligent digital multimeter with 10000 counts, which offers a high measuring range and high resolution. It can accurately measure AC/DC voltage, AC/DC current, 10 A current and can also be used to test conductivity, capacitance, frequency, duty cycle, resistance, diode, temperature, NCV, live wire detection, etc. It is suitable for various electronic maintenance fields such as mechanical engineering, laboratories, automobiles and home appliances. It is equipped with a 1500 mAh lithium battery and a 2.4' TFT full-color display with a resolution of 240 x 320 pixels. Specifications Function Range Accuracy DC voltage 9.999 V/99.99 V/999.9 V ±(0.5%+3) AC voltage 9.999 V/99.99 V/750.0 V ±(1%+3) DC current 9999 uA/99.99 mA/999.9 mA/9.999 A ±(1.2%+3) AC current 9999 uA/99.99 mA/999.9 mA/9.999 A ±(1.5%+3) Resistance 9.999 MΩ/999.9 KΩ/99.99 KΩ/9.999 KΩ/999.9 Ω ±(1.5%+3) 99.99 MΩ ±(1.5%+3) Capacitance 999.9 µF/99.99 µF/9.999 µF/999.9 nF/99.99 nF/9.999 nF ±(2.0%+3) 9.999 mF/99.99 mF ±(5.0%+3) Frequency 9.999 MHz/999.9 KHz/9999 KHz/9.999 KHz/999.99 Hz/99.99 Hz/9.999 Hz ±(0.1%+3) Temperature -55~1300°C (-64~2372°F) ±(2.5%+3) Diode Yes Continuity test Yes NVC Yes Live wire detection Yes Max counts 10000 counts Battery capacity 1500 mAh Dimensions 155 x 80 x 36 mm Weight 191 g Included 1x FNIRSI DMT-99 Multimeter 2x Test pens 1x USB-C charging cable 1x Manual Downloads Manual Firmware V2.4

Read more less

2 Channels • 350 MHz • 1 GSa/s • 50,000 wfm/s • 7 inch Touchscreen The FNIRSI DPOS350P is a sleek 4-in-1 powerhouse in tablet form! This compact and portable device packs serious functionality: it combines a 2-channel oscilloscope (350 MHz), a signal generator (50 MHz), a frequency response analyzer (50 MHz), and a spectrum analyzer (200 kHz–350 MHz) – all in one unit. Whether you're in R&D, troubleshooting, or field testing, the DPOS350P delivers the tools you need to measure, generate, analyze, and visualize electronic signals with precision and clarity. Its responsive high-resolution touchscreen and intuitive controls make signal analysis fast, flexible and efficient. Features Powerful Multi-Function Integration 350 MHz 2-channel oscilloscope with 1 GSa/s real-time sampling 50 MHz signal generator with 14 standard + custom waveforms Spectrum analyzer (200 kHz–350 MHz): Perfect for EMI, RF & HF testing Frequency response analyzer (FRA) up to 50 MHz High-Performance Waveform Capture 50,000 wfm/s refresh rate for real-time signal clarity 350 MHz bandwidth (single-channel mode) Detects rare and low-probability anomalies Crisp Display & Smooth Operation 7" IPS touchscreen (1024 x 600 resolution) Switch between grayscale and color temperature display Easy to operate in various test environments Reliable, Protected & Fast-Charging High-voltage protection up to 400 V Fast charging with QC 18 W (full charge in 2 hours) Built for stable long-term operation Data Storage & Export Save up to 500 waveform records + 90 screenshots USB export for easy reporting and offline analysis Specifications General Display 7 inch (IPS full viewing angle) Resolution 1024 x 600 pixels Interaction mode Capacitive touch screen Total power consumption 10 W Power-on configuration 5 presets Charging QC 18 W, 12 V/1.5 A (USB-C) Battery 3.7 V, 8000 mAh lithium battery Battery life approx. 3 hours in operation, 5 hours standby Heat dissipation Air cooling Expansion interface USB data port Automatic shutdown 15~60 minutes / off Firmware upgrade Support .iso image upgrade Languages English / Portuguese / Russian / Chinese Dimensions 190 x 128 x 37 mm Oscilloscope Analog channels 2 Analog bandwidth 350 MHz Rise time 1ns Real-time sampling rate 1 GSa/s Memory depth 60 Kpts Input impedance 1 MΩ / 14PF Time base range 5ns ~ 50s Roll time base 50ms ~ 50s Vertical sensitivity 2 mV ~ 20 V (1X) Vertical range 16 mV ~ 160 V (1X) DC accuracy ±2% Time accuracy ±0.01% Input coupling DC / AC Probe attenuation 1X / 10X / 100X Hardware bandwidth limit 150M / 20M High resolution mode 8bit ~ 16bit Parameter measurements 12 types Cursor measurement Time, period, frequency, level, voltage Trigger detection Digital trigger Trigger channel CH1 / CH2 Trigger mode Auto / Single / Normal Trigger edge Rising edge / Falling edge Trigger suppression L1 ~ L3 Trigger level Manual / automatic 10% ~ 90% Screenshot storage 90 pictures Waveform storage 500 groups Background grid Display / hide Waveform movement Coarse adjustment / fine adjustment Overvoltage protection Withstand voltage 400 V Waveform brightness Adjustable Simple FFT display Yes Digital fluorescence Yes Color temperature display Yes X-Y mode Yes ZOOM time base Yes One-key automatic adjustment Yes One-key return to zero Yes Data browser Yes Signal Generator Waveform types 14 standard functions + captured waveform Frequency 0~50 MHz (sine wave only, other waveforms up to 10M/5M/3M) Amplitude 0~5 VPP Offset -2.5 V ~ +2.5V Duty cycle 0.1~99.9% Frequency resolution 1 Hz Amplitude resolution 1 mV Offset resolution 1 mV Duty cycle resolution 0.1% Customizable captured waveform 500 groups Frequency Response Analyzer (FRA) Excitation signal frequency 100 Hz ~ 50 MHz Excitation signal amplitude 0~5 VPP Excitation signal offset -2.5V ~ +2.5V Excitation frequency count 20~500 Cursor measurement Frequency / gain / phase Operating mode Single / cyclic System calibration Yes Spectrum Analyzer Conversion method FFT FFT length 4K ~ 32K Frequency range 200 KHz ~ 350 MHz Level range -60 dBmV ~ +260 dBmV Cursor measurement Frequency / amplitude Marking parameter Maximum energy harmonic Waterfall chart Yes 3D waterfall chart Yes Automatic adjustment Yes System calibration Yes Included 1x FNIRSI DPOS350P (4-in-1) 2x 350 MHz Probes 1x QC 18 W Fast Charger (EU) 1x USB Data Cable 1x Alligator Clip 1x Storage Bag 1x Manual Downloads Manual Firmware

Read more less

The FNIRSI DPOX180H is a cost-effective handheld dual-channel digital phosphor oscilloscope and signal generator. The oscilloscope has a real-time sampling rate of 500 MS/s and an analog bandwidth of 180 MHz. The measurement results are displayed on the high-contrast 2.8-inch IPS full-view LCD screen with digital fluorescence technology. Features 2-ch handheld oscilloscope & DDS signal generator 180 MHz bandwidth 500 MS/s sampling rate 20 MHz signal generator Innovative digital trigger system Cursor measurement function 5 mV sensitivity 50000 wfm/s waveform refresh rate 2.8" IPS full-vision high-definition display Built-in 4.2 V/3000 mAh lithium battery Automatic shutdown setting High-voltage anti-burning protection Specifications Nummer of channels 2 Analog bandwidth 180 MHz Maximum sampling rate 500 MS/s Input coupling DC/AC Rise time 2.5s Storage depth 120 Kpts Input impedance 1 MQ-18 PF Vertical sensitivity 5 mV-10 V (1X) Time base range 5 nS~50 S DC accuracy ±2% Time accuracy +0.01% Trigger detection Digital trigger Trigger mode Auto/Single/Normal Trigger edge Rising/Falling Measurement range 40 mV~80 V (1X) Screenshot storage 90 Capture signal 500 Screen size 2.8 inch Screen resolution 320 x 240 Display technology IPS full view Expansion interface USB transmission interface Auto power off 5 minutes - 2 hours Firmware upgrade Supported iso image upgrade Charging requirements 5 V/2 A Battery capacity 3000 mAh Standby time 3.5 hours at full charge Signal Generator 14 standard function signals Waveform storage 250 groups Parameter measurement 12 kinds Dimensions 135 x 90 x 40 mm Digital Phosphor Oscilloscope FNIRSI DPOX180H Oscilloscope uses the latest digital phosphor technology to overcome the traditional oscilloscope due to noise caused by the waveform burr feeling. Color temperature display function can more clearly see the distribution of the signal, probability characteristics and the rise and fall time of the step signal fast and slow. X-Y mode with digital phosphor technology for comparison of amplitude, frequency and phase of two groups of signals. DDS Function Signal Generator Built-in 20 MHz DDS function signal generator, with 14 kinds of standard function signals, output amplitude fixed at 1 VPP, sine wave frequency of 20 MHz, other waveform frequency of 10 MHz, adjustable frequency step of 1 Hz. Contains the original chopping technology, intercept part of the oscilloscope measurement of complex signals as the output signal of the signal generator, than the traditional signal generator hand-drawn signal more objective and realistic. Included 1x FNIRSI DPOX180H phosphor oscilloscope 2x Probes (200 MHz) 1x USB power supply 1x USB cable 1x Manual Downloads Manual Firmware V40

Read more less

The FNIRSI DPS150 is a high-performance adjustable DC power supply that features a USB-C input interface and multiple power supply modes, allowing precise adjustment of output voltage (0-30 V) and current (0-5 A). It provides efficient, low-consumption, and stable output, equipped with multiple safety protection functions including overvoltage, overcurrent, overload, overheating, and reverse connection. It can be flexibly applied to serial connection of multiple devices, with rich and user-friendly display and operation, compact and portable design, meeting various application needs. Features 30 V, 5 A, 150 W variable DC power with 0.01 V, 0.001 A precision, CC/CV modes, and <20 mV ripple to protect sensitive electronics. Supports PC, QC, and DC inputs with programmable outputs and 6 preset voltage/current settings. Compatible with 4 mm banana plugs, U-shaped terminals, and copper wires for various equipment. 8 safety mechanisms including overvoltage, current, short circuit, and overheating protection. 2.8-inch HD IPS screen with 90° flip, numerical and curve displays for easy monitoring. Small, space-saving design for use in labs, repairs, and DIY projects. Specifications Input Voltage 5~32 V DC Input Current 100 mA-5 A Output Voltage 0-30 V Output Current 0~5 A Output Power 0-150 W Input Way PD fast charger QC fast charger Power bank DC power adapters Operating Environment 0-40°C Load Regulation 0.49% Full Load Efficiency 96.30% Display 2.8 inch (320 x 240) Dimensions 106 x 76 x 28 mm Weight 178 g Included 1x DPS150 Power Supply 2x Alligator clip wires (black & red) 1x Micro USB cable 1x Manual Downloads Manual Firmware V0.0.1

Read more less

The FNIRSI DPS150 is a high-performance adjustable DC power supply that features a USB-C input interface and multiple power supply modes, allowing precise adjustment of output voltage (0-30 V) and current (0-5 A). It provides efficient, low-consumption, and stable output, equipped with multiple safety protection functions including overvoltage, overcurrent, overload, overheating, and reverse connection. It can be flexibly applied to serial connection of multiple devices, with rich and user-friendly display and operation, compact and portable design, meeting various application needs. Features 30 V, 5 A, 150 W variable DC power with 0.01 V, 0.001 A precision, CC/CV modes, and <20 mV ripple to protect sensitive electronics. Supports PC, QC, and DC inputs with programmable outputs and 6 preset voltage/current settings. Compatible with 4 mm banana plugs, U-shaped terminals, and copper wires for various equipment. 8 safety mechanisms including overvoltage, current, short circuit, and overheating protection. 2.8-inch HD IPS screen with 90° flip, numerical and curve displays for easy monitoring. Small, space-saving design for use in labs, repairs, and DIY projects. Specifications Input Voltage 5~32 V DC Input Current 100 mA-5 A Output Voltage 0-30 V Output Current 0~5 A Output Power 0-150 W Input Way PD fast charger QC fast charger Power bank DC power adapters Operating Environment 0-40°C Load Regulation 0.49% Full Load Efficiency 96.30% Display 2.8 inch (320 x 240) Dimensions 106 x 76 x 28 mm Weight 178 g Included 1x DPS150 Power Supply 2x Alligator clip wires (black & red) 1x C2C PD charging cable 1x 100 W PD GaN Adapter (EU) 1x Micro USB cable 1x Manual Downloads Manual Firmware V0.0.1

Read more less

The FNIRSI DSO153 is a highly practical and cost-effective handheld oscilloscope with a real-time sampling rate of 5 MSa/s, 1 MHz bandwidth, and complete triggering function (single, normal, auto). It can be used freely for both periodic analog signals and non-periodic digital signals, and can measure up to ±400 V voltage with an efficient one-click AUTO, which can display the measured waveform without complicated adjustments. Additionally, it features a function signal generator capable of outputting 14 types of signals (10 KHz). Equipped with a 2.8-inch 320x240 resolution HD LCD screen and a built-in 1000 mAh high-quality lithium battery, it can be used for about 4 hours when fully charged. Features 2.8-inch HD LCD display with 320x240 Resolution Portable Pocket Oscilloscope with Signal Generator Lightweight, mini-sized, assembled Faster sampling: 5 MS/s, 1 MHz bandwidth Versatile triggering: Single, Normal, Auto User-friendly: One-button setup Extended battery: 1000 mAh, 4 hours Multi-functionality: 10 KHz Sine Wave Generator Specifications Bandwidth 1 MHz Sampling rate 5 MSa/s Vertical Sensitivity 10mV/Div – 20V/Div Time Base Range 500ns/Div – 20s/Div Voltage Range X1: ±40 V (Vpp: 80 V)X10: ±400 V (Vpp: 800 V) Trigger Method Auto / Normal / Single Coupling Method AC/DC Frequency Range 0-10 KHz Duty Cycle Range 0-100% Amplitude Range 0.1-3.3 V Display 2.8 inches (Resolution: 320 x 240) USB Charging 5 V/1 A Lithium Battery Capacity 1000 mAh Dimensions 99 x 68.3 x 19.5 mm Weight 100 g Included 1x FNIRSI DSO153 Oscilloscope 1x P6100 oscilloscope probe 1x Adapter 1x Alligator clip probe 1x USB charging cable 1x Lanyard 1x Manual Downloads Manual Firmware V1.1.8

Read more less

The DSO510 oscilloscope was designed for complex signal testing, research, and development. Ideal for professionals and educational use, it ensures precise measurements with ease. With a 48 MS/s real-time sampling rate and 10 MHz bandwidth, it supports both analog and digital signals. Its complete trigger modes (Single, Normal, Auto) and ±400 V voltage range deliver reliable accuracy. The one-click AUTO mode simplifies waveform display. A built-in 50 KHz signal generator adds versatility, while the 2.8-inch HD LCD screen and 1000 mAh battery provide clear visuals and up to 4 hours of use. Features Oscilloscope: 10 MHz bandwidth, 48 MS/s sampling rate, ±400 V voltage range. Signal Generator: 50 KHz Display: 2.8" HD TFT (320 x 240) Interface: USB-C Design: Fully assembled, lightweight, ideal for maintenance tasks. Trigger Functions: Single, normal, automatic modes. Signal Support: Handles periodic analog and non-periodic digital signals. One-Click AUTO Mode: Instantly displays waveforms without complex setup. Battery: Built-in 1000 mAh lithium battery with up to 4 hours of usage per charge. Language Support: English, German, Spanish, Portuguese, Russian, Chinese, Korean, Japanese. Specifications Channel 1 Bandwidth 10 MHz Sampling Rate 48 MS/s Vertical Sensitivity 10 mV/Div-20 V/Div Time Base Range 50 ns/Div-20 s/Div Measurement Values 22 kinds Trigger Mode Auto/Normal/Single Voltage Range X1: ±40 V (Vpp: 80 V)X10: ±400 V (Vpp: 800 V) Trigger Edge Rising/Falling Coupling AC/DC Frequency 0-50 KHz Duty Cycle 0-100% (rectangular and sawtooth waves) Amplitude 0.1-3.0 V Waveforms Sine, rectangular, sawtooth, half, full, step, anti step, exponential rise, exponential drop, DC signal, multi tone, Sink pulse, Lorentz. Display 2.8-inch (320 x 240 pixels) USB Charging 5 V/1 A Lithium Battery Capacity 1000 mAh Dimensions 99 x 68.3 x 19.5 mm Weight 104 g Included 1x FNIRSI DSO510 Oscilloscope 1x P6100 oscilloscope probe 1x Adapter 1x Alligator clip probe 1x USB charging cable 1x Lanyard 1x Manual Downloads Manual Firmware V1.0.4

Read more less

The FNIRSI DWS-200 is a powerful 200 W smart soldering station, ideal for electronic soldering applications. Powered by a switch-mode power supply, it operates smoothly with a wide voltage input range of 100-240 V. The station provides an adjustable temperature range from 100°C to 450°C (212°F to 842°F) and allows for easy switching between °C and °F. To enhance efficiency, it supports up to three preset temperature values and can connect to a soldering iron stand for standby mode activation. The station also features a dynamic temperature curve mode for real-time data monitoring, ensuring precise and consistent performance in demanding soldering tasks. Features Maximum power output of 200 W, allowing for fast heating Wide adaptive voltage input of 100-240 V 2.8" HD color TFT display with intelligent control Multiple preset groups to switch between different settings quickly Supports F245 and F210 soldering handle types, offering flexibility for different soldering applications Real-time sleep mode to extend the life of the soldering tip Multi-mode real-time monitoring for power and temperature status, enhancing safety and precision Specifications Peak Power 200 W (max) Temperature Range 100°C~450°C (212°F~842°F) Display 2.8" TFT HD Color Screen Heating Time 1 sec Melting Time 3 sec Input Voltage 100-240 V (AC) Input Fuse 3 A Soldering Handle Type F245 Dimensions (Station) 156 x 96 x 103 mm Weight (Station) 475 g Included 1x FNIRSI DWS-200 Soldering Station 1x Soldering Handle F245 6x Soldering Tips (B, KU, K, C2, I, JS) 1x Connecting Cable 2x Helping Hands 1x Power Cable (EU) Downloads Manual Firmware V1.3

Read more less

The FNIRSI FNAC-28 is a versatile USB tester that functions as a voltage/current meter and quick charge trigger. Supporting up to 6.5 A bidirectional current detection via USB-A and USB-C, it features a high-precision 16-bit ADC for accurate measurements. With multi-functional data analysis, fast charge protocol support (QC, VOOC, WARP, etc.), and cable resistance detection, it’s ideal for detailed power and charging diagnostics. Features Bidirectional High Current Detection: Supports up to 6.5 A bidirectional current detection. Compatible with USB-A and USB-C interfaces, it accurately measures both power supply and power consumption, providing users with detailed data support. High-Precision Measurement Chip: Equipped with an external 16-bit ADC, the USB power meter ensures precise voltage and current measurements, effectively minimizing error and enhancing test accuracy. Multifunctional Data Analysis: Supports battery capacity testing and stores up to 5 data sets. It also features curve display, waveform pause, and an adjustable time base for detailed data observation. Fast Charging Protocol Support: Supports QC2.0/QC3.0, FCP/SCP, AFC, VOOC/WARP, and SVOOC 1.0/2.0 triggering. All supported protocols are automatically detected to meet a wide range of testing needs. Cable Detection and Simulation: Using the differential pressure method, the USB detector measures cable internal resistance, simulates APPLE 2.4 A and DASH fast charging, and reads DASH cable information. Specifications Resolution Accuracy Display 1.06" full-color TFT LCD screen Monitored Voltage 4~24 V 0.001 V ±(0.2‰+2) Monitored Current 0~6.5 A 0.001 A ±(0.2‰+2) Monitored Power 0~156 W 0.001 W ±(0.2‰+2) Protocol Detection QC2.0: 5 V/9 V/12 V/20 V QC3.0: 3.4-20 V FCP: 9 V/12 V/20 V SCP: 5.5-6.0 V AFC: 9 V/12 V VOOC/WARP: 20 V SVOOC 1.0: Yes SVOOC 2.0: Yes Temperature display °C/°F switch Languages English and Chinese Cable Resistance Yes Detect DASH Cable Yes Soft DASH Cable Yes Soft APPLE 2.4A Yes Brightness Adjustment Yes Standby Time Setting Yes Firmware Upgrade Yes Dimensions 73 x 36 x 12 mm Weight 21 g Included 1x FNIRSI FNAC-28 USB Tester 1x USB cable 1x Manual Downloads Manual FNIRSI USB Meter for PC (Windows/Linux) FNIRSI Bluetooth App (Android) Manual_USB Meter PC Software Manual_Android Bluetooth App

Read more less

The FNIRSI FNB58 USB tester (with Bluetooth) is a comprehensive and very accurate USB voltage and current meter. It features a 2.0-inch full-color HD TFT display, built-in USB-A, micro USB and USB-C interface. With this device you can measure the power supply or power consumption of products or the charging power of cell phones and power supplies. You can also determine the fast charging protocol of chargers. Features USB-A and USB-C interface 2.0" HD display Data at a glance Wide compatibility Ultra-precise data detection Play with fast charging technology Automatic protocol detection (PD2.0, 3.0, 3.1, PPS, QC2.0, 3.0, FCP, SCP, AFC, PE, DASH VOOC, SuperVOOC and more) Simple user interface, easy to operate 4 function curve displays (real-time voltage and current curve, offline curve recording, D+/D- voltage curve, high-speed power supply ripple measurement) Cable detection 10 groups of energy recording battery capacity calculation PC connectivity for data logging and firmware updates Bluetooth app for Android devices Specifications Voltage range 4-28 V Current range 0-7 A Power range 0-120 W Load equivalent internal resistance 0-9999.9 Ω D+/D- voltage 0-3.3 V Capacity 0-9999.99 Ah Power consumption 0-9999.99 Wh Cable resistance 0-9999.9 Ω Interfaces micro USB, USB-A, USB-C Dimensions 42 x 13 x 82 mm Downloads Manual Firmware V0.68

Read more less

The FNIRSI GC-02 nuclear radiation detector offers a sleek, portable design with high-precision Geiger-Müller counters for accurate detection of ionizing radiation (γ-rays, X-rays, etc.). Its 1.5-inch HD LCD screen displays real-time, average, max, and cumulative values. Features include alarm settings, customizable sleep/shutdown times, timed monitoring, and history viewing with up to 10 saved records. The 850 mAh rechargeable battery provides up to 6 hours of use. Compact and reliable, the FNIRSI GC-02 is perfect for on-the-go nuclear radiation detection. Features Food and Metal Detection Marble and Ore Inspection Nuclear Industry Radioactivity Detection Radioactive Medical Equipment Testing Multifunctional Real-Time Monitoring Core Technology: Geiger-Müller Counter High-Capacity 850 mAh Battery Detector: Energy Compensation GM Tube (Geiger Counter Tube) Detection Ray Types: Gamma Rays, X-Rays, Beta Rays Specifications Detection Radiation Type Ionizing radiation (γ-rays, X-rays, etc.) Detector Energy compensation GM tube (Geiger counter tube) Dose Current Rate 0.00-1000 μSv/h (1 mSv/h) Cumulative Dose Equivalent 0.00 μSv-500.0 mSv Energy Range 48 keV-15 Mev ≤±30% (for 137Cs -) Sensitivity 80 CPM/uSv (for Co-60) Dosage Unit μSv/h, μGy/h, mR/h, CPS, CPM Battery Capacity 850 mAh Alarm Method Light, Sound Languages Chinese, English, Russian, German, Japanese, Portuguese, Spanish, Korean Dimensions 106.5 x 44.5 x 25 mm Included 1x GC-02 Nuclear Radiation Detector 1x USB cable 1x Lanyard loop Downloads Manual

Read more less

The FNIRSI HRM-10 is a portable, high-precision battery internal resistance and voltage tester. This device offers true four-wire measurement and is designed for both accuracy and ease of use. It automatically measures internal resistance and voltage values simultaneously, displaying the results on its HD color screen. Users have the option to manually adjust voltage and resistance ranges to suit their needs. The device also includes a sorting mode that automatically filters the good and bad batteries based on user-set thresholds. Additionally, it supports the storage of historical data and allows for exporting measurement records in table format. Features High Measurement Accuracy Tabular Data Export Auto-Evaluate Measurement Results 8 Threshold Settings HD Color Screen Folding Stand 1000 mAh Lithium Battery Specifications Voltage Resistance Measuring range 0-100 V (DC) 0-200 Ω Accuracy ±0.5% ±0.5% Gear Automatic, 1 V, 10 V, 100 V Automatic, 20 mΩ, 200 mΩ, 2 Ω, 20 Ω, 200 Ω Instrument test signal frequency 1 Khz (AC) Rechargeable USB-C (5 V/1 A) Built-in battery 1000 mAh lithium battery User calibration Yes Sorting mode Yes History record Yes Recorded data export Yes Working environment –10°C to +45°C, relative humidity <80% Storage environment –20°C to +80°C, relative humidity <80% Dimensions 158.7 x 80.5 x 28.4 mm Weight 225 g Included 1x FNIRSI HRM-10 Internal Resistance Tester 1x Clip Test Line 1x USB-C data cable 1x Manual Downloads Manual Firmware V0.3

Read more less

The FNIRSI HS-02A is an improved version of the HS-01 soldering iron with a better grip and a shorter tip for more comfort and precision during use. It features a larger 0.96-inch IPS HD color display that allows for better visibility of settings and status. With an output power of 100 W, the HS-02A heats up quickly and reaches operating temperature in about 2 seconds. The temperature is adjustable in a range of 100-450°C (212-842°F) to meet different soldering requirements. Features Temperature: 100-450°C (212-842°F) Accurate temperature adjusting and control Fast heating CNC Metal Shell Adaptive Power 100 W High Power Protocols: PD, QC Specifications Temperature Range 100-450°C (212-842°F) Working Voltage 9-20 V Display 0.96" IPS HD Color Screen Power Supply USB-C Fast Charging Protocols PD / QC Power 100 W (max) Dimensions 180 x 20 mm Weight 61 g Included 1x FNRISI HS-02A Smart soldering iron 6x Soldering iron tips (HS02A-KU, HS02A-K, HS02A-JS, HS02A-I, HS02A-C2, HS02A-B) 1x 100 W USB-C power supply (EU) 1x DC to USB-C power cable 1x USC-C charging cable 1x Mini soldering iron stand 1x Manual Downloads Manual Firmware V1.7

Read more less

The FNIRSI IR40 is a compact, high-precision and fast distance measuring device with Bluetooth integration, rechargeable battery, USB-C charging port and app connection. Features It features a high precision of ±2 mm, up to 40 m measurement range, and an 8 cm skin-friendly feeling. With an intelligent algorithm, it will make the distance measurement in an instant. Has versatile functions, including single measurement, multiple measurements, area measurement, volume measurement, Pythagorean, second Pythagorean, front and rea reference, and unit switching. FNIRSI IR40 laser rangefinder is equipped with a ROHM acceleration sensor, realizes auto flip. Built-in 400 mAh battery, it can be charged with a USB-C charging port quickly. When fully charged, it can offer up to 3000 times of continuous measurement. It supports Android & iOS systems, and Link APP to realize functions such as data synchronization/remarks, length/area/volume calculation, floor plan drawing, real-time recording, etc. Specifications Measurement range 0.05~40 m Measurement accuracy ±2 mm Laser type 620-670 nm Measurement time 0.1~3s Resolution 1 mm Units m/ft/in Dimensions 79 x 34.5 x 19 mm Included FNIRSI IR40 Rangefinder USB cable Manual Downloads Manual Android App iOS App

Read more less