Elektor Arduino Nano MCCAB Training Board

  • BrandElektor Labs

Description

The Elektor Arduino Nano MCCAB Training Board contains all the components (incl. Arduino Nano) required for the exercises in the "Microcontrollers Hands-on Course for Arduino Starters", such as light-emitting diodes, switches, pushbuttons, acoustic signal transmitters, etc. External sensors, motors or assemblies can also be queried or controlled with this microcontroller training system.

Specifications (Arduino Nano MCCAB Training Board)

Power Supply Via the USB connection of the connected PC or an external power supply unit (not included)
Operating Voltage +5 Vcc
Input Voltage All inputs 0 V to +5 V
VX1 and VX2 +8 V to +12 V (only when using an external power supply)
Hardware periphery LCD 2x16 characters
Potentiometer P1 & P2 JP3: selection of operating voltage of P1 & P2
Distributor SV4: Distributor for the operating voltages
SV5, SV6: Distributor for the inputs/outputs of the microcontroller
Switches and buttons RESET button on the Arduino Nano module 6x pushbutton switches K1 ... K6 6x slide switches S1 ... S6 JP2: Connection of the switches with the inputs of the microcontroller
Buzzer Piezo buzzer Buzzer1 with jumper on JP6
Indicator lights 11 x LED: Status indicator for the inputs/outputs LED L on the Arduino Nano module, connected to GPIO D13 JP6: Connection of LEDs LD10 ... LD20 with GPIOs D2 ... D12
Serial interfaces
SPI & I²C		 JP4: Selection of the signal at pin X of the SPI connector SV12 SV9 to SV12: SPI interface (3.3 V/5 V) or I²C interface
Switching output for external devices SV1, SV7: Switching output (maximum +24 V/160 mA, externally supplied) SV2: 2x13 pins for connection of external modules
3x3 LED matrix
(9 red LEDs)		 SV3: Columns of the 3x3 LED matrix (outputs D6 ... D8) JP1: Connection of the rows with the GPIOs D3 ... D5
Software Library MCCABLib Control of hardware components (switches, buttons, LEDs, 3x3 LED matrix, buzzer) on the MCCAB Training Board
Operating Temperature Up to +40 °C
Dimensions 100 x 100 x 20 mm


Specifications (Arduino Nano)

Microcontroller ATmega328P
Architecture AVR
Operating Voltage 5 V
Flash Memory 32 KB, of which 2 KB used by bootloader
SRAM 2 KB
Clock Speed 16 MHz
Analog IN Pins 8
EEPROM 1 KB
DC Current per I/O Pins 40 mA on one I/O pin, total maximum 200 mA on all pins together
Input Voltage 7-12 V
Digital I/O Pins 22 (6 of which are PWM)
PWM Output 6
Power Consumption 19 mA
Dimensions 18 x 45 mm
Weight 7 g

Included

  • 1x Elektor Arduino Nano Training Board MCCAB
  • 1x Arduino Nano
Product form

The Elektor Arduino Nano MCCAB Training Board contains all the components (incl. Arduino Nano) required for the exercises in the... Read more

Pre-order

€ 74,95€ 64,95 incl. VAT
Members identical

    Details

    SKU: 20295
    EAN: 7442105131181

    Description

    The Elektor Arduino Nano MCCAB Training Board contains all the components (incl. Arduino Nano) required for the exercises in the "Microcontrollers Hands-on Course for Arduino Starters", such as light-emitting diodes, switches, pushbuttons, acoustic signal transmitters, etc. External sensors, motors or assemblies can also be queried or controlled with this microcontroller training system.

    Specifications (Arduino Nano MCCAB Training Board)

    Power Supply Via the USB connection of the connected PC or an external power supply unit (not included)
    Operating Voltage +5 Vcc
    Input Voltage All inputs 0 V to +5 V
    VX1 and VX2 +8 V to +12 V (only when using an external power supply)
    Hardware periphery LCD 2x16 characters
    Potentiometer P1 & P2 JP3: selection of operating voltage of P1 & P2
    Distributor SV4: Distributor for the operating voltages
    SV5, SV6: Distributor for the inputs/outputs of the microcontroller
    Switches and buttons RESET button on the Arduino Nano module 6x pushbutton switches K1 ... K6 6x slide switches S1 ... S6 JP2: Connection of the switches with the inputs of the microcontroller
    Buzzer Piezo buzzer Buzzer1 with jumper on JP6
    Indicator lights 11 x LED: Status indicator for the inputs/outputs LED L on the Arduino Nano module, connected to GPIO D13 JP6: Connection of LEDs LD10 ... LD20 with GPIOs D2 ... D12
    Serial interfaces
    SPI & I²C    		 JP4: Selection of the signal at pin X of the SPI connector SV12 SV9 to SV12: SPI interface (3.3 V/5 V) or I²C interface
    Switching output for external devices SV1, SV7: Switching output (maximum +24 V/160 mA, externally supplied) SV2: 2x13 pins for connection of external modules
    3x3 LED matrix
    (9 red LEDs)    		 SV3: Columns of the 3x3 LED matrix (outputs D6 ... D8) JP1: Connection of the rows with the GPIOs D3 ... D5
    Software Library MCCABLib Control of hardware components (switches, buttons, LEDs, 3x3 LED matrix, buzzer) on the MCCAB Training Board
    Operating Temperature Up to +40 °C
    Dimensions 100 x 100 x 20 mm


    Specifications (Arduino Nano)

    Microcontroller ATmega328P
    Architecture AVR
    Operating Voltage 5 V
    Flash Memory 32 KB, of which 2 KB used by bootloader
    SRAM 2 KB
    Clock Speed 16 MHz
    Analog IN Pins 8
    EEPROM 1 KB
    DC Current per I/O Pins 40 mA on one I/O pin, total maximum 200 mA on all pins together
    Input Voltage 7-12 V
    Digital I/O Pins 22 (6 of which are PWM)
    PWM Output 6
    Power Consumption 19 mA
    Dimensions 18 x 45 mm
    Weight 7 g

    Included

    • 1x Elektor Arduino Nano Training Board MCCAB
    • 1x Arduino Nano

    Customer Reviews

    Be the first to write a review
    0%
    (0)
    0%
    (0)
    0%
    (0)
    0%
    (0)
    0%
    (0)

    Login

    Forgot password?

    Don't have an account yet?
    Create an account