Raspberry Pi Kits

The project book, written by well-known Elektor author Dogan Ibrahim, is an introduction to using the Raspberry Pi Pico Experimenting Kit. The kit is based on the Raspberry Pi Pico processor and includes several on-board as well as external sensors, and an actuator. The kit is programmed using the MicroPython programming language. The Thonny development environment (IDE) is used in all the projects in the book. All the projects given in the book have been fully tested and are working. No prior programming or electronic experience are required to follow the projects.The book’s fully evaluated projects feature all the supplied components. Each project includes a block diagram, a circuit diagram, a full program listing, and a complete program description.Included in the bundle Raspberry Pi Pico RP2040 Pico Expansion Board 1.44-inch TFT LCD with ST7735 driver 3x Pushbutton input 3x LED output 1x Active buzzer 6x Interfaces (UART/GPIO/I²C/ADC) Grove-compatible Powered by Micro-USB 8 Modules MPU6050 6-axis IMU DHT11 humidity & temperature sensor 10 A relay SG90 servo Slide potentiometer Serial-to-WiFi (ESP8266) module Ultrasonic range sensor 8-bit RGB addressable LED (WS2818) module Project book (178 pages) 42 Projects in the BookBoard-Hardware-Based Projects Flashing an on-board LED Flashing SOS Flashing LED – using a timer Alternately flashing LEDs Pushbutton control Changing the LED flashing rate using pushbutton interrupts Binary counting LEDs Randomly flashing yellow, green, and blue LEDs Chasing LEDs Reaction timer Buttons and LEDs The TFT Display Second counter Event counter Reaction timer Display LED and button status Temperature and humidity – display in Thonny window Temperature and humidity – LED output Temperature and humidity – display on TFT ON/OFF temperature control ON/OFF temperature control – setting the desired temperature Voltmeter Changing the brightness of an LED Ultrasonic distance measurement - display in Thonny window Ultrasonic distance measurement - display on TFT Height of a person (stadiometer) Ultrasonic reverse-parking aid with buzzer Ultrasonic liquid level controller Melody maker Servo motor control Accurate servo motor control WS2812 LED strip light show - state machine approach WS2812 LED strip light show – using the neopixel library WS2812 LED strip show – another neopixel library example Displaying 3 dimensions of acceleration A car’s maximum acceleration – using the TFT display Level display using the gyroscope MPU6050 temperature display TFT display test TFT bitmap display Using the WiFi Connect to the local Wi-Fi network and display the IP address Controlling an LED from a smartphone using Wi-Fi Displaying the temperature on a smartphone using Wi-Fi

Read more less

Now save more than €30 with this Starter Kit compared to buying them separately! This Raspberry Pi 5 Ultimate Starter Kit includes everything you need to get started right away with the latest version of the world's most popular mini computer as a development and multimedia device. Kit Contents Raspberry Pi 5 (8 GB RAM)The new Raspberry Pi 5 delivers more performance than ever before. Thanks to the faster CPU, GPU and RAM, Raspberry Pi 5 is up to 3x faster than its already fast predecessor. 64-bit quad-core ARM Cortex-A76 processor (2.4 GHz) VideoCore VII GPU (800 MHz) 8 GB of LPDDR4X RAM (4267 MHz) Raspberry Pi silicon RP1 I/O controller chip Real-time clock On/off button PCIe 2.0 UART connector Fan connector Official 27 W Power Supply for Raspberry Pi 5 (EU, white)The official Raspberry Pi 27 W PD USB-C power supply is designed specifically to power the Raspberry Pi 5. microSD Card pre-installed with Raspberry Pi OS (32 GB)With this microSD (32 GB, Class 10) with pre-installed Raspberry Pi OS you can start using your Raspberry Pi right away. Official Case for Raspberry Pi 5 (white/red)The Raspberry Pi 5 case offers improved thermal features to support the higher peak power consumption of the Raspberry Pi 5. Active Cooler for Raspberry Pi 5The active cooler provides an alternative cooling solution for users who wish to use their Raspberry Pi 5 under sustained heavy load without a case. Official HDMI Cable for Raspberry Pi (white, 1 m)The official Raspberry Pi micro-HDMI to HDMI (A/M) cable (white, 1 m) is designed for the Raspberry Pi. FPC Camera Cable for Raspberry Pi 5 (200 mm)With this cable you can connect your current Raspberry Pi camera products to the Raspberry Pi 5. FPC Display Cable for Raspberry Pi 5 (200 mm)With this cable you can connect your current Raspberry Pi display products to the Raspberry Pi 5. Book: Raspberry Pi 5 Essentials – Program, build, and master over 60 projects with Python This 322-page book (written by the best-selling author Dogan Ibrahim) starts with an introduction to the Raspberry Pi 5 computer and covers the important topics of accessing the computer locally and remotely. Use of the console language commands as well as accessing and using the desktop GUI are described with working examples. The remaining parts of the book cover many Raspberry Pi 5-based hardware projects using components and devices such as LEDs and buzzers, LCDs, Ultrasonic sensors, Temperature and atmospheric pressure sensors, The Sense HAT, Camera modules.

Read more less

Raspberry Pi-based Eye Catcher A standard sand clock just shows how time passes. In contrast, this Raspberry Pi Pico-controlled sand clock shows the exact time by “engraving” the four digits for hour and minute into the layer of sand. After an adjustable time the sand is flattened out by two vibration motors and everything begins all over again. At the heart of the sand clock are two servo motors driving a writing pen through a pantograph mechanism. A third servo motor lifts the pen up and down. The sand container is equipped with two vibration motors to flatten the sand. The electronic part of the sand clock consists of a Raspberry Pi Pico and an RTC/driver board with a real-time clock, plus driver circuits for the servo motors. A detailed construction manual is available for downloading. Features Dimensions: 135 x 110 x 80 mm Build time: 1.5 to 2 hours approx. Included 3x Precut acrylic sheets with all mechanical parts 3x Mini servo motors 2x Vibration motors 1x Raspberry Pi Pico 1x RTC/driver board with assembled parts Nuts, bolts, spacers, and wires for the assembly Fine-grained white sand

Read more less

Features Suitable for Raspberry Pi + GPIO Extension Board Exquisite appearance DIY operation Specifications Size of GPIO Extension Board: 7.5 x 6 cm (3 x 2.4') Size of Breadboard: 16.5 x 5.5 x 1 cm (6.5 x 2.2 x 0.4') Included 1x GPIO Extension Board 1x Breadboard 1x 40P Pin Connect Line 8x 1K Resistor 8x 10K Resistor 4x LED (yellow) 4x LED (red) 4x Key 10x 25 mm Jumper Wires A 10x 25 mm Jumper Wires B

Read more less

Contents 1x High Quality Retail Box 10x 1/4W 1% 100R Resistor 10x 1/4W 1% 220R Resistor 10x 1/4W 1% 330R Resistor 10x 1/4W 1% 1K Resistor 10x 1/4W 1% 10K Resistor 10x 1/4W 1% 100K Resistor 10x 1/4W 1% 4.7K Resistor 10x 1/4W 1% 47K Resistor 10x 100PF Ceramic Capacitor 10x 10NF Ceramic Capacitor 10x 100NF Ceramic Capacitor 10x 22PF Ceramic Capacitor 10x 10UF aluminum electrolytic capacitor 10x 470UF aluminum electrolytic capacitor 10x Red LED 10x Green LED 10x Yellow LED 10x Blue LED 8x 12x12x7.3 Switch 2x Red Cap 2x Yellow Cap 2x Green Cap 2x Blue Cap 1x 10K Precision Potentiometer 2x RGB LED 1x Active Buzzer 1x Passive Buzzer 1x Pin Header 1x40 1x Resistor Card 1x 400pts Breadboard 1x 30pcs/pack Breadboard Jumper Wires Set

Read more less

Now save more than €30 with this Starter Kit compared to buying them separately! This Raspberry Pi 5 Ultimate Starter Kit includes everything you need to get started right away with the latest version of the world's most popular mini computer as a development and multimedia device. Kit Contents Raspberry Pi 5 (4 GB RAM)The new Raspberry Pi 5 delivers more performance than ever before. Thanks to the faster CPU, GPU and RAM, Raspberry Pi 5 is up to 3x faster than its already fast predecessor. 64-bit quad-core ARM Cortex-A76 processor (2.4 GHz) VideoCore VII GPU (800 MHz) 4 GB of LPDDR4X RAM (4267 MHz) Raspberry Pi silicon RP1 I/O controller chip Real-time clock On/off button PCIe 2.0 UART connector Fan connector Official 27 W Power Supply for Raspberry Pi 5 (EU, white)The official Raspberry Pi 27 W PD USB-C power supply is designed specifically to power the Raspberry Pi 5. microSD Card pre-installed with Raspberry Pi OS (32 GB)With this microSD (32 GB, Class 10) with pre-installed Raspberry Pi OS you can start using your Raspberry Pi right away. Official Case for Raspberry Pi 5 (white/red)The Raspberry Pi 5 case offers improved thermal features to support the higher peak power consumption of the Raspberry Pi 5. Active Cooler for Raspberry Pi 5The active cooler provides an alternative cooling solution for users who wish to use their Raspberry Pi 5 under sustained heavy load without a case. Official HDMI Cable for Raspberry Pi (white, 1 m)The official Raspberry Pi micro-HDMI to HDMI (A/M) cable (white, 1 m) is designed for the Raspberry Pi. FPC Camera Cable for Raspberry Pi 5 (200 mm)With this cable you can connect your current Raspberry Pi camera products to the Raspberry Pi 5. FPC Display Cable for Raspberry Pi 5 (200 mm)With this cable you can connect your current Raspberry Pi display products to the Raspberry Pi 5. Book: Raspberry Pi 5 Essentials – Program, build, and master over 60 projects with Python This 322-page book (written by the best-selling author Dogan Ibrahim) starts with an introduction to the Raspberry Pi 5 computer and covers the important topics of accessing the computer locally and remotely. Use of the console language commands as well as accessing and using the desktop GUI are described with working examples. The remaining parts of the book cover many Raspberry Pi 5-based hardware projects using components and devices such as LEDs and buzzers, LCDs, Ultrasonic sensors, Temperature and atmospheric pressure sensors, The Sense HAT, Camera modules.

Read more less

Contents Raspberry Pi Pico RP2040 Development Board 30 cm Micro:bit flat USB cable for Smart Car 10-Pin Male to Female Dupont Line Three-leaf Fan Blue Motor Bracket with Screw 3 V DC motor with wire ULN2003 Driver Board Stepper Motor Green 28 mm Leg LED 5 mm Red (1pcs) 28 mm Leg LED 5 mm Green (1pcs) 28 mm Leg LED 5 mm Yellow (1pcs) 28 mm Leg LED 5 mm Blue (1pcs) Resistor 220R 1/4W 1% (1pcs) 400 Points Soldless Breadboard Infrared Obstacle Avoidance Tracking Sensor Module Active Alarm Buzzer Driver Module Low Current Blue 7 Color Flashing LED Module Tachile Switch Module

Read more less

This 'All in One' Raspberry Pi 4 Desktop Starterkit contains all official parts and allows an easy and quick start! Raspberry Pi 4 Desktop Kit contains: Raspberry Pi US Keyboard & Mouse 2x micro HDMI to Standard HDMI cable (A/M) 1 m Raspberry Pi 15.3 W USB-C Power Supply (EU version) Raspberry Pi 4 Case Official Raspberry Pi Beginner's Guide (English language) 16 GB NOOBS with Raspbian microSD card Raspberry Pi 4 B is NOT included.

Read more less

This kit includes 2 servo motors and a Monk Makes ServoSix interface board for use with Raspberry Pi. It also includes a Raspberry Leaf GPIO template, a bunch of female-to-female header pins and a 4xAA battery box.Features of the Servo Six board Screw terminals for servo power supply Reverse-polarity protection for the servo power supply 470 µF 16 V capacitor for servo supply 470 Ω current limiting resistors for servo control lines (to protect GPIO pins) Power indicator LE DownloadsInstructions

Read more less

The kit ships with a comprehensive guide booklet. The booklet covers the basic setup and then how to complete each of the 7 experiments. Each experiment is complete with detailed circuit diagrams, explanations, and a complete code run-through. This means that you can get started without having to understand too much Python.The Raspberry Pi Pico board, a new low cost, high-performance microcontroller. The board features a powerful new, Raspberry Pi designed ARM-based dual-core chip-- the RP2040. The pico also features 64KB of internal RAM and support for up to 16MB of off-chip Flash. A wide range of flexible I/O options includes I2C, SPI, and Programmable I/O (PIO). These support endless possible applications for this small and affordable board.The kit is programmed using MicroPython. This is a full Python 3 implementation created specifically for small embedded microcontrollers, such as the Pico and the popular BBC micro:bit. You will use the Thonny editor to create your code, which can then be saved directly to the Pico from the editor via USB. Thonny is a Python Editor/IDE designed to allow beginners to get up and running with Python coding with as little fuss as possible.A power pack is not required as power will be supplied via the USB connection to the computer that the Thonny editor is running on.Features This kit offers a great introduction to microcontrollers, Python coding, and physical computing. Make the 7 experiments in the step-by-step tutorial book and learn as you go. All parts are included to conduct the 7 experiments. The kit is supplied with a detailed booklet that covers setup and then how to complete the 7 experiments. The experiments explore; simple coding, Interrupts, Threads, Digital Inputs, and Analog and Digital Outputs. Once you have completed all of the included experiments, you have the perfect prototyping system for further learning/prototyping with the Raspberry Pi Pico board. Included is a large format breadboard for ease of prototyping. The kit is supplied in re-usable packaging suitable for long term storage of the kit. Contents 1x Large Prototype Breadboard 2x Red 5mm LED 2x Yellow 5mm LED 2x Green 5mm LED 10x 330Ω Resistor 1x Piezo Element Buzzer 20x Male to Male Jumper Wires 2x Push Switches A booklet guide containing basic setup information and the following 7 experiments Exp. 1 - Show Me The Light Exp. 2 - Control an Input Exp. 3 - Interrupt Me Exp. 4 - Making a Noise Exp. 5 - So Many Interruptions Exp. 6 - Rub Head and Pat Tummy - Threads Exp. 7 - Building a System from the Blocks we have Learnt The kit is supplied in re-usable packaging suitable for long term storage of the kit. Requires USB Lead Raspberry Pi Pico Pin Headers

Read more less

Your gateway to IoT and microcontroller programming With 450+ components and 117 online projects, this comprehensive kit ignites your creativity. The tutorials by Paul McWhorter make learning enjoyable for beginners and advanced users. This kit supports MicroPython, C/C++, and Piper Make, offering diverse programming options. Explore sensors, actuators, LEDs, and LCDs for endless project possibilities. From home automation to robotics, this kit empowers your tech journey. Features IoT Starter Kit for Beginners: This kit offers a rich IoT learning experience for beginners. With 450+ components, 117 projects, and expert-led video lessons, this kit makes learning microcontroller programming and IoT engaging and accessible. Expert-Guided Video Lessons: The kit includes 27 video tutorials by the renowned educator, Paul McWhorter. His engaging style simplifies complex concepts, ensuring an effective learning experience in microcontroller programming. Wide Range of Hardware: The kit includes a diverse array of components like sensors, actuators, LEDs, LCDs, and more, enabling you to experiment and create a variety of projects with the Raspberry Pi Pico W. Supports Multiple Languages: The kit offers versatility with support for three programming languages - MicroPython, C/C++, and Piper Make, providing a diverse programming learning experience. Dedicated Support: Benefit from our ongoing assistance, including a community forum and timely technical help for a seamless learning experience. Included Raspberry Pi Pico W Breadboard Jumper Wires Resistor Transistor Capacitor Diode Li-po Charger Module 74HC595 TA6586 – Motor Driver Chip LED RGB LED LED Bar Graph 7-segment Display 4-Digit 7-Segment Display LED Dot Matrix I²C LCD1602 WS2812 RGB 8 LEDs Strip Buzzer DC Motor Servo DC Water Pump Relay Button Micro Switch Slide Switch Potentiometer Infrared Receiver Joystick Module 4x4 Keypad MPR121 Module MFRC522 Module Photoresistor Thermistor Tilt Switch Reed Switch PIR Motion Sensor Module Water Level Sensor Module Ultrasonic Module DHT11 Humiture Sensor MPU6050 Module Documentation Online Tutorials in 3 languages (EN, DE and JP)

Read more less

The Speaker Kit for Raspberry Pi is a small amplified speaker designed for the Raspberry Pi. Included MonkMakes Amplified Speaker Set of 10 female to female header wires Short stereo audio lead Raspberry Leaf GPIO template Downloads Instructions Datasheet

Read more less

The Joy-Pi Advanced is a compact and powerful device that allows you to realize your projects quickly and easily. Whether you already have a lot of experience, or next to none, the Joy-Pi Advanced lets you unleash your creativity. Thanks to its compatibility with a wide range of platforms, including Raspberry Pi, Raspberry Pi Pico, Arduino Nano, BBC micro:bit, and NodeMCU ESP32, you can easily and quickly access your preferred platform. In addition, the Joy-Pi Advanced features more than 30 stations, lessons, and modules, giving you an unlimited variety of ways to get your projects done. With the self-developed learning center, you can not only improve your skills but also create new projects. The learning center offers a wealth of information and tutorials that will guide you step by step through your projects. Joy-Pi Advanced is characterized in particular by its intelligent switch units, which allow an extended use of the available pins. A total of three switch units are integrated, each equipped with 12 individual switches that provide precise control of the connected sensors and modules. This system solves the well-known problem of limited pin count that occurs with conventional microcontrollers. The switch units allow you to operate a large number of sensors and modules in parallel by switching them on and off individually. This simulates multiple pin assignment, allowing you to exploit the full power of your projects without compromising functionality. By combining innovative adapter boards and the micro:bit slot, you can achieve seamless compatibility with a wide range of microcontrollers such as Raspberry Pi Pico, NodeMCU ESP32, micro:mit and Arduino Nano. The specially developed adapter boards are designed to perfectly match the respective microcontroller. By plugging the microcontroller onto the appropriate adapter board and then plugging it into the micro:bit slot, the Joy-Pi Advanced quickly and easily becomes compatible with the different microcontrollers. This allows seamless integration of your preferred platform and the ability to combine the strengths of the different microcontrollers in your projects. This way, you can fully focus on your creative projects without worrying about the compatibility of different microcontrollers. The Joy-Pi Advanced simplifies the development process and gives you the possibility to design your projects flexibly and individually. Features Highly integrated development platform & learning center Fast, easy & wireless combination of various sensors & actuators Installation option for Raspberry Pi 4 Compatible with various microcontrollers Self-developed, didactic learning platform for Raspberry Pi & Windows Specifications Compatible to Raspberry Pi 4, Arduino Nano, NodeMCU ESP32, BBC micro:bit, Raspberry Pi Pico Installed sensors, actuators & components 39 Learning platform Over 40 entries in the know-ledge database, 10 projects, 10 learning tasks, 14 visions Displays 7-segment display, 16x2 display, 1.8“ TFT display, 0.96“ OLED display, 8x8 RGB matrix Sensors DS18B20, shock sensor, hall sensor, barometer, sound sensor, gyroscope, PIR sensor, Light barrier, NTC, Light sensor, 6x touch sensor, color sensor, ultrasonic distance sensor, DHT11 temperature & humidity sensor Control Joystick, 5x switches, potentiometer, rotary encoder, 4x4 button matrix, relays, PWM fan Motors Servo interface, Stepper motor interface, Vibration motor Measuring & conversion modules Analog-Digital Converter, Level converter, voltmeter, Variable voltage supply Other components RTC real time clock, buzzer, EEPROM memory, infrared receiver, breadboard, RFID reader Adapter boards Adapter for NodeMCU ESP32, Arduino Nano & Raspberry Pi Pico, Board connectors for Raspberry Pi & External Boards Electronic components Infrared remote control, RFID chip, RFID card, 6x alligator clips, microSD card reader, servo motor, stepper motor, 32 GB microSD card Components 40x resistors, 3x green LEDs, 3x yellow LEDs, 3x red LEDs, 1x transistor, 5x buttons, 1x potentiometer, 2x capacitors Other accessories Screw assortment, screwdriver, accessory storage bag, power supply & power cable, servo mount Power supply Built-in power supply: 36 W, 12 V, 3 A Case connector: Small device plug C8 Voltage outputs 12 V, 5 V, 3.3 V, Variable voltage output (2-11 V) Data buses & signal outputs I²C, SPI, Analog to digital converter Battery (RTC) CR2032 Dimensions 327 x 200 x 52 mm Required Raspberry Pi 4 Downloads Joy-Pi website Datasheet Manual

Read more less

Features Get Started with Raspberry Pi Pico easily and quickly 14 handpicked Grove Modules, including 5 sensors/ 5 actuators/ 2LED/ 1 LCD display/ 1 Grove shield Detailed and comprehensive Micropython tutorials for each module (Arduino Guide is on the way) No wiring, no welding, plug & play experience Included 1 x Grove - LED Pack 1 x Grove - RGB LED (WS2813 Mini) 1 x Grove - Light Sensor 1 x Grove - Sound Sensor 1 x Grove - Rotary Angle Sensor 1 x Grove - Temperature & Humidity Sensor 1 x Grove - mini PIR motion sensor 1 x Grove - Passive Buzzer 1 x Grove - Button 1 x Grove - Servo 1 x Grove - Mini Fan 1 x Grove - Relay 1 x Grove - 16x2 LCD 1 x Grove Shield for Pi Pico 8 x Grove Cable

Read more less

Features Easy-to-use and low-cost hardware kit: combines an affordable hardware kit with FREE curriculums and activities for students’ hands-on experience in precision agriculture techniques to food production. New tools for STEAM Education learners: students learn about AI, Machine learning, and IoT by building a garden monitoring system. Easily use with Raspberry Pi 4: with atmospheric and environmental sensors to understand their soil's health, analyze data, and make decisions. Real-time data collection: The student-built IoT devices connect to custom Microsoft Excel workbooks that collect real-time data using Excel’s Data Streamer. Building your own Machine Learning models: using Lobe.ai, students apply the technique to predict nutrient deficiencies in their plants and identifying pests in their garden. Introducing Microsoft responsible AI framework: engaging students with some of the social and ethical challenges raised by this new technology. Applications Combined with software and curriculum & resources, you can get hands-on experience, learn about artificial intelligence, machine learning, the Internet of Things, data science and then apply the knowledge in growing plants in the real world. This kit is highly suitable for use in different scenarios, no matter in the classroom, at home, at maker spaces/ fab labs or through distance learning courses: School garden monitoring Home garden monitoring Distance teaching /learning Online courses Hobby and DIY projects Included 1x Grove Base Hat for Raspberry Pi with a Fan 1x One Wire Temperature Sensor 1x Grove Capacitive Soil Moisture Sensor 1x Grove Sunlight Sensor 1x Grove Temperature & Humidity Sensor 1x Grove Relay 1x Grove Dual Button 1x micro SD Card with Card Reader (32 GB) 1x USB to TTL Serial Cable 1x Screwdriver Downloads FarmBeats for Student Kit Brochure FarmBeats Student Image

Read more less

Features Abundant Expandability- You can add a hard drive by merely adding the nylon standoff and acrylic board. The OpenMediaVault includes services such as SSH, (S)FTP, SMB/CIFS, DAAP media servers, RSync, BitTorrent clients. The E-Ink screen makes it more power-efficient. It provides you with an excellent visual experience, which is used to display Raspberry Pi's CPU temperature, CPU usage, disk usage, fan power, etc. Simple product composition, accessories with corresponding numbers, and providing detailed tutorials make it easy to set up. Dual fans and heat sinks installed, working automatically when the CPU temperature exceeds 54 degrees, quickly and effectively solving the heating problem of Raspberry pi motherboard. Specification for E-Ink Working voltage：3.3 V Communication interface： 3-wireSPI, 4-wireSPI Dimensions: 59.2 mm x 29.2 mm x 1.05 mm Display size: 48.55 mm x 23.71 mm Pitch: 0.194 x 0.194 Resolution: 250 x 122 Display color: black and white Gray level: 2 Global refresh: 2s Refresh function: 26.4 Mw (Typ.) Standby power consumption < 0.017 Mw Viewing angle > 170 ° If the manual refresh mode is set, you will need to press OK to refresh. In auto mode, the E-Ink screen will refresh automatically every 500 ms; Package List 1 x NAS HAT 3 x NAS 3 mm transparent acrylic 1 x Micro SD card (8 G) 1 x SATA to USB hard drive cable ( length 0.45 M) 1 x Screwdriver 4 x Silicone Pad 1 x Dual fan 3 x Heat sink 10 x M2 x 12 Screws 10 x M2 Nut 14x M3 x 8 mm Screws 10 x M2.5 x 6 mm Screws 6 x M3 x 26 mm Nylon Standoff 6 x M3 x 13 + 6 mm Single-pass Nylon Standoff 6 x M2.5 x 11 mm Nylon Standoff 6 x M2.5 x 8 + 6 mm single-pass Nylon Standoff NOTE: It is recommended to use the RPi 4B with the SunFounder NAS Kit together, as the USB3.0 interface can provide you with higher file transfer efficiency. The SunFounder NAS Kit currently only supports the expansion of two hard-drive.

Read more less

GrovePi+ is stacked on top of the Raspberry Pi without the need for any other connections. Communication between the two occurs over the I2C interface. All Grove modules connect to the universal Grove connectors on the GrovePi+ shield via the universal 4 pin connector cable. Grove modules work on analog and digital signals and can be connected directly to the ATMEGA328 microcontroller on the Grove Pi+. The microcontroller acts as an interpreter between the Raspberry Pi and the Grove sensors. It sends, receives, and executes commands sent by the Raspberry Pi. Features One GrovePi+ board together with 12 popular Grove sensors and 10 Grove cables GrovePi+ is compatible with Raspberry Pi A+, B, B+ / 2, 3, 4. CE certified and compatible with Linux and Win 10 IoT. Included 1x Grove Pi+ 1x Grove - Rotary Angle Sensor 1x Grove - Sound Sensor 1x Grove - LCD RGB Backlight 1x Grove - Temp&Humi Sensor 1x Grove - Red LED 1x Grove - Light Sensor 1x Grove - Buzzer 1x Grove - Relay 1x Grove - Blue LED 1x Grove - Button 1x GrovePi+ Guidebook 10x Cables 1x Grove - UItrasonic Ranger 1x Grove - Green LED

Read more less

The Voice Interaction Satellite Kit can extend the reach of your base station to each room in your house and enable you to interact with the hardware based on where you issue your commands! You can arrange multiple Satellite Kits throughout your home to add new functionality to Base kit or any other smart speaker, extending your voice control across several rooms. The Voice Interaction Satellite Kit is powered by a Raspberry Pi Zero W and the ReSpeaker 2-Mics Pi HAT. Along with the kit comes a speaker, a Grove - Temperature Humidity Sensor (SHT31) sensor, a Grove Relay, and a pegboard to hang it on a wall or create a nifty stand. Please note: All Satellite Kits require a Base kit (link to Snips Voice Interaction Base Kit) or Raspberry Pi 3B+ in order to operate as intended.

Read more less

World’s Most Popular ROS Platform TurtleBot is the most popular open source robot for education and research. The new generation TurtleBot3 is a small, low cost, fully programmable, ROS based mobile robot. It is intended to be used for education, research, hobby and product prototyping. Affordable Cost TurtleBot was developed to meet the cost-conscious needs of schools, laboratories and companies. TurtleBot3 is the most affordable robot among the SLAM-able mobile robots equipped with a 360° Laser Distance Sensor LDS-01. Small Size The dimension of TurtleBot3 Burger is only 138 x 178 x 192 mm (L x W x H). Its size is about 1/4 of the size of the predecessor. Imagine keeping TurtleBot3 in your backpack and develop your program and test it anywhere you go. ROS Standard The TurtleBot brand is managed by Open Robotics, which develops and maintains ROS. Nowadays, ROS has become the go-to platform for all the roboticists around the world. TurtleBot can be integrated with existing ROS-based robot components, but TurtleBot3 can be an affordable platform for whom want to get started learning ROS. Extensibility TurtleBot3 encourages users to customize its mechanical structure with some alternative options: open source embedded board (as a control board), computer and sensors. TurtleBot3 Burger is a two-wheeled differential drive type platform but it is able to be structurally and mechanically customized in many ways: Cars, Bikes, Trailers and so on. Extend your ideas beyond imagination with various SBC, sensors and motors on a scalable structure. Modular Actuator for Mobile Robot TurtleBot3 is able to get a precise spatial data by using 2 DYNAMIXEL’s in the wheel joints. DYNAMIXEL XM series can be operated by one of 6 operating modes (XL series: 4 operating modes): Velocity control mode for wheels, Torque control mode or Position control mode for joint, etc. DYNAMIXEL can be used even to make a mobile manipulator which is light but can be precisely controlled with velocity, torque and position control. DYNAMIXEL is a core component that makes TurtleBot3 perfect. It is easy to assemble, maintain, replace and reconfigure. Open Control Board for ROS The control board is open-sourced in hardware wise and in software wise for ROS communication. The open source control board OpenCR1.0 is powerful enough to control not only DYNAMIXEL’s but also ROBOTIS sensors that are frequently being used for basic recognition tasks in cost effective way. Various sensors such as Touch sensor, Infrared sensor, Color sensor and a handful more are available. The OpenCR1.0 has an IMU sensor inside the board so that it can enhance precise control for countless applications. The board has 3.3 V, 5 V, 12 V power supplies to reinforce the available computer device lineups. Strong Sensor Lineups TurtleBot3 Burger uses enhanced 360° LiDAR, 9-Axis Inertial Measurement Unit and precise encoder for your research and development. Open Source The hardware, firmware and software of TurtleBot3 are open source which means that users are welcomed to download, modify and share source codes. All components of TurtleBot3 are manufactured with injection molded plastic to achieve low cost, however, the 3D CAD data is also available for 3D printing. Specifications Maximum translational velocity 0.22 m/s Maximum rotational velocity 2.84 rad/s (162.72 deg/s) Maximum payload 15 kg Size (L x W x H) 138 x 178 x 192 mm Weight (+ SBC + Battery + Sensors) 1 kg Threshold of climbing 10 mm or lower Expected operating time 2h 30m Expected charging time 2h 30m SBC (Single Board Computers) Raspberry Pi 4 (2 GB RAM) MCU 32-bit ARM Cortex-M7 with FPU (216 MHz, 462 DMIPS) Actuator XL430-W250 LDS (Laser Distance Sensor) 360 Laser Distance Sensor LDS-01 or LDS-02 IMU Gyroscope 3 AxisAccelerometer 3 Axis Power connectors 3.3 V/800 mA5 V/4 A12 V/1 A Expansion pins GPIO 18 pinsArduino 32 pin Peripheral 3x UART, 1x CAN, 1x SPI, 1x I²C, 5x ADC, 4x 5-pin OLLO DYNAMIXEL ports 3x RS485, 3x TTL Audio Several programmable beep sequences Programmable LEDs 4x User LED Status LEDs 1x Board status LED1x Arduino LED1x Power LED Buttons and Switches 2x Push buttons, 1x Reset button, 2x Dip switch Battery Lithium polymer 11.1 V 1800 mAh / 19.98 Wh 5C PC connection USB Firmware upgrade via USB / via JTAG Power adapter (SMPS) Input: 100-240 VAC 50/60 Hz, 1.5 A @maxOutput: 12 VDC, 5 A Downloads ROS Robot Programming GitHub E-Manual Community

Read more less

pi-top [4] is a game-changing, programmable computing device that combines digital making, coding, and practical projects. With pi-top [4], educators, students, and inventors get to design, code, and make anything they can imagine using one simple, easy-to-use system. From beginner to superuser, pi-top powers your projects and brings learning into the real world. Every pi-top [4] comes with our Foundation Kit, a metal ‘bento box’ containing 14 components, including programmable sensors, buttons, and LEDs. Get started right away by learning the basics of coding and physical computing, then continue your learning by progressing into guided lesson plans in advanced coding, robotics, cybersecurity, and AI. With pi-top [4], kids can not only do cool electronic projects and learn to code using Scratch 3 and Mu, but they can also use it as a regular computer. It comes with the Chromium web browser, as well as Google Suite giving them access to Gmail, Docs, Sheets, and other productivity and publishing software. They can also unleash their creativity with images and music. How about using Photo Editor, mtPaint, or ImageMagic to edit photos and graphics, or Sonic Pi to create fantastic music? pi-top [4] is a machine for making, a PC for homework, and an entertainment device, so it is an excellent choice for a child’s first computer. Compatibility and connectivity is the name of the game! pi‑top [4] can be connected to any monitor, but you can also use other devices to access all our fantastic software. You can easily connect pi‑top [4] to your existing Windows, Apple, and Chromebook computers, giving you access to pi-topOS on your current laptop. Interacting with pi-top [4] couldn't be more open and accessible! Third-party products such as Arduino and Micro:Bit are also supported, and with Raspberry Pi GPIO connectivity as standard, you have instant access to thousands of free projects and resources that utilize the Raspberry Pi HAT architecture. pi-top [4] is powered by the 1.5 GHz quad-core Raspberry Pi 4 and comes with 4 GB of RAM so that you can apply it to a range of power-hungry complex tasks including video editing and image manipulation. pi-top [4] plays nicely with natural construction products you might already own, such as LEGO and Meccano. What you get: Contents of the pi-top [4] 1x pi-top [4] 1x Raspberry Pi 4 (4 GB RAM) 1x 16 GB SD card with pi-topOS 1x Power Supply 1x pi-top Display Cable 1x HDMI Adapter 1x USB Adapter Contents of the Foundation Kit 1x Foundation Plate 1x Sound Sensor 1x Light Sensor 2x Button 2x Buzzer 2x Potentiometer 2x LEDs (red) 2x LEDs (green) 2x LEDs (yellow) 1x Ultrasonic Sensor 8x LEGO Connector

Read more less

World’s Most Popular ROS Platform TurtleBot is the most popular open source robot for education and research. The new generation TurtleBot3 is a small, low cost, fully programmable, ROS based mobile robot. It is intended to be used for education, research, hobby and product prototyping. Affordable Cost TurtleBot was developed to meet the cost-conscious needs of schools, laboratories and companies. TurtleBot3 is the most affordable robot among the SLAM-able mobile robots equipped with a 360° Laser Distance Sensor LDS-01. ROS Standard The TurtleBot brand is managed by Open Robotics, which develops and maintains ROS. Nowadays, ROS has become the go-to platform for all the roboticists around the world. TurtleBot can be integrated with existing ROS-based robot components, but TurtleBot3 can be an affordable platform for whom want to get started learning ROS. Extensibility TurtleBot3 encourages users to customize its mechanical structure with some alternative options: open source embedded board (as a control board), computer and sensors. TurtleBot3 Waffle Pi is a two-wheeled differential drive type platform but it is able to be structurally and mechanically customized in many ways: Cars, Bikes, Trailers and so on. Extend your ideas beyond imagination with various SBC, sensors and motors on a scalable structure. Modular Actuator for Mobile Robot TurtleBot3 is able to get a precise spatial data by using 2 DYNAMIXEL’s in the wheel joints. DYNAMIXEL XM series can be operated by one of 6 operating modes (XL series: 4 operating modes): Velocity control mode for wheels, Torque control mode or Position control mode for joint, etc. DYNAMIXEL can be used even to make a mobile manipulator which is light but can be precisely controlled with velocity, torque and position control. DYNAMIXEL is a core component that makes TurtleBot3 perfect. It is easy to assemble, maintain, replace and reconfigure. Open Control Board for ROS The control board is open-sourced in hardware wise and in software wise for ROS communication. The open source control board OpenCR1.0 is powerful enough to control not only DYNAMIXEL’s but also ROBOTIS sensors that are frequently being used for basic recognition tasks in cost effective way. Various sensors such as Touch sensor, Infrared sensor, Color sensor and a handful more are available. The OpenCR1.0 has an IMU sensor inside the board so that it can enhance precise control for countless applications. The board has 3.3 V, 5 V, 12 V power supplies to reinforce the available computer device lineups. Open Source The hardware, firmware and software of TurtleBot3 are open source which means that users are welcomed to download, modify and share source codes. All components of TurtleBot3 are manufactured with injection molded plastic to achieve low cost, however, the 3D CAD data is also available for 3D printing. Specifications Maximum translational velocity 0.26 m/s Maximum rotational velocity 1.82 rad/s (104.27 deg/s) Maximum payload 30 kg Size (L x W x H) 281 x 306 x 141 mm Weight (+ SBC + Battery + Sensors) 1.8 kg Threshold of climbing 10 mm or lower Expected operating time 2h Expected charging time 2h 30m SBC (Single Board Computers) Raspberry Pi 4 (2 GB RAM) MCU 32-bit ARM Cortex-M7 with FPU (216 MHz, 462 DMIPS) Remote Controller RC-100B + BT-410 Set (Bluetooth 4, BLE) Actuator XL430-W210 LDS (Laser Distance Sensor) 360 Laser Distance Sensor LDS-01 or LDS-02 Camera Raspberry Pi Camera Module v2.1 IMU Gyroscope 3 AxisAccelerometer 3 Axis Power connectors 3.3 V/800 mA5 V/4 A12 V/1 A Expansion pins GPIO 18 pinsArduino 32 pin Peripheral 3x UART, 1x CAN, 1x SPI, 1x I²C, 5x ADC, 4x 5-pin OLLO DYNAMIXEL ports 3x RS485, 3x TTL Audio Several programmable beep sequences Programmable LEDs 4x User LED Status LEDs 1x Board status LED1x Arduino LED1x Power LED Buttons and Switches 2x Push buttons, 1x Reset button, 2x Dip switch Battery Lithium polymer 11.1 V 1800 mAh / 19.98 Wh 5C PC connection USB Firmware upgrade via USB / via JTAG Power adapter (SMPS) Input: 100-240 VAC 50/60 Hz, 1.5 A @maxOutput: 12 VDC, 5 A Downloads ROS Robot Programming GitHub E-Manual Community

Read more less

TurtleBot 4 is the next-generation of the world’s most popular open source robotics platform for education and research, offering better computing power, better sensors and a world class user experience at an affordable price point.TurtleBot 4 Lite is equipped with an iRobot Create 3 mobile base, a powerful Raspberry Pi 4 running ROS 2, OAK-D spatial AI stereo camera, 2D LiDAR and more. All components have been seamlessly integrated to deliver an out-of-the-box development and learning platform.Specifications Base platform iRobot Create 3 Wheels (Diameter) 72 mm Ground Clearance 4.5 mm On-board Computer Raspberry Pi 4 (4 GB) Maximum linear velocity 0.31 m/s in safe mode0.46 m/s without safe mode Maximum angular velocity 1.90 rad/s Maximum payload 9 kg Operation time 2h 30m – 4h depending on load Charging time 2h 30m Lidar RPLIDAR A1M8 Camera OAK-D-Lite User Power VBAT @1.9 A5 V @ Low current3.3 V @ Low current USB Expansion 2x USB 2.0 (Type A)2x USB 3.0 (Type A) Programmable LEDs Create 3 Lightring Buttons and Switches 2x Create 3 User buttons1x Create 3 Power Button Battery 26 Wh Lithium Ion (14.4 V nominal) Charging Dock Included Size (L x W x H) 342 x 339 x 192 mm Weight 3.3 kg DownloadsUser Manual

Read more less